A Paradigm can be Shifted

When a plant engineer has to purchase a compressed air dryer his first thought will be what dewpoint is required. This will then depend on the application; specifications of machinery using compressed air will guide the engineer as will codes of practice such as BRC/BCAS for the Food Industry. If a negative dewpoint is required then a desiccant dryer will be selected. The genre is likely to be well known to the engineer and will attract a significant capital and running cost particularly if a lower capital cost heatless dryer is selected. However the solution is classic and cannot be faulted. The alternative scenario is for the positive dewpoint at typically +2º C and again the engineer will know that a refrigeration type dryer will handle this application with relatively low capital and running cost but that he must take care not to have pipework going below the dewpoint temperature.

There is a third solution which is mostly ignored or perhaps is not fully understood. This is the membrane type dryer and BEKO TECHNOLOGIES offer their DRYPOINT M range of membrane dryers alongside their EVERDRY and DRYPOINT RA, desiccant and fridge dryers. Steve Riley, General Manager of BEKO TECHNOLOGIES in the UK and Ireland comments “I was amazed at how many DRYPOINT M’s were being sold when I joined the company. A little research told me
that 20,000 units had been sold since launch, in the UK alone. I could guess that many purchasers were “Original Equipment Manufacturers” because the main benefit I had in my mind was the very small footprint. I knew also that some compressor manufacturers had a packaged unit which included a membrane dryer but I couldn’t for the life of me guess the diversity of applications”.

He was correct in his thinking but later researches told him that there were very good reasons for engineers to select DRYPOINT M just on overall cost. This needs some explanation as what tends to put most engineers off is waste and it is a fact that membrane dryers lose a quantity of compressed air in purge loss. However this is not fixed and BEKO’s sales people have software which enables the choice of a low capital cost, higher purge loss unit or a higher capital cost and lower purge loss unit of energy cost is important (and when isn’t it). Riley comments again “I don’t think anyone will be too surprised to know that one of the other statistics I wanted to understand quickly was what maintenance revenue I would get from all these units. It was an unbelievable number- Nothing, £0 and it is not a short lived product that if a problem should occur it is more economical to throw it away. It is possible to destroy the membrane by having too much liquid ingress but BEKO’s experience and design team have produced a dryer with close coupled separator and drain to protect against this eventuality.” In fact there are no wearing or replaceable parts.

Comments

Post a Comment

Popular posts from this blog

Han® HC 250 high current contact

A Powerful Solution HARTING has developed the new Han® HC 250high current connector as a powerful interface that impresses by requiring little space, transmitting high current intensities and allowing flexible configuration of the number of poles. The HC 250 one-pole crimp module can be connected in various frame geometries to produce the required number of poles in a compact space – and in the existing Han® HPR housing. Technical details: - Rated current 250 A at a rated voltage of 2000 V - Termination cross-sections are: 35 mm2, 50 mm2 and 70 mm2 - Maximum four-pole interfaces in a size 24 B HPR housing, making it particularly suitable for motor connections - High quality plastic with good smoke and inflammability levels - Removal tool for simple installation and removal of the contacts and inserts - Confusion of a number of interfaces is reliably prevented by multiple coding options for the individual inserts The requirements in the railway industry are changing, as
Read more

EGCS-D0 Accelerometer Now Available in 10,000g Range

Measurement Specialties, Inc. (NASDAQ: MEAS) has recently redesigned the EGCS-D0 accelerometer to enable it to accurately and reliably measure up to ±10,000g. This rugged device is critically damped, which is the ideal mechanism to protect the accelerometer against ±20,000g impacts and prevent sensor ringing. The EGCS-D0 accelerometer is now available in ranges from ±5g to ±10,000g which makes it ideal for both critical low-g measurements and high-g impacts. These units feature a Wheatstone Bridge mV output with a standard compensated temperature range of 20ºC to 80ºC (other options available). The EGCS-D0 was specifically designed for impact and shock testing in auto safety, aerospace, military and civil engineering applications. Designed to be bolt-mounted, this device operates from 2-15Vdc excitation with electrical output ratiometric to voltage input. Optional triaxial mounting blocks (MTG-F4), signal conditioners (Model 101) and auto-zero inline amplifiers (Model 140) are avai
Read more
Ilix Cermet Reamers Are Ideal For Dry Machining Engineers Cutting Tools, the UK agent for Ilix, has introduced Ilix solid-carbide and cermet reamers for the machining of hard metals. The machine reamers 6372C and 6323 allow the production of high-precision holes with good surface finish. Compared with HSS, the solid-carbide qualities enable the increase of cutting parameters and tool life. The quality of the reamers is said to guarantee high performance, even for hard metals with a resistance more than 1200N/mm2. The Ilix carbide 6372C range of hundredth reamers is from 0.98mm through to 12.05mm in increments of 0.01mm. The reamers are manufactured to a tolerance of +0.000 - +0.004mm. The cermet reamers 6323 have new cutting geometry developed by Ilix. These reamers are said to be ideal for steel machining, having high chemical stability during the cutting process. They offer good wear resistance due to the high hardness and have low material adhesion. The Ilix cermet reamer is said to
Read more