Bruel And Kjaer Helps To Test Lift Sound Quality

Orona has used Bruel and Kjaer's Head and Torso Simulator (HATS), binaural microphones and Pulse sound-quality software to analyse the sound-quality behaviour of its lifts. This equipment allowed it to correlate the sound quality with the different noise sources and to study the most appropriate ways to improve lift comfort. Orona (manufacturer of lifts), Mondragon Goi Eskola Politeknikoa (MGEP [Engineering Faculty of Mondragon University]) and Ikerlan (Research Centre) formed a consortium to investigate the sound quality in Orona's lifts.

According to Unai Galfarsoro, the coordinator of the acoustic and vibration group at Mondragon University: 'The reason for establishing the sound-quality project is the need to go beyond the traditional A-weighted sound pressure level, which is usually used to rank different noise sources, because we believe that a complete sound-quality analysis gives wider and more reliable results.

'The objective is to analyse the actual sound-quality performance of the various types of Orona lifts, to correlate the sound quality with the different noise sources and to study the most suitable approaches to improve the comfort of the lifts,' he added. Before carrying out the sound-quality process, the types of lifts to be analysed were selected and six of each type were tested. Three up and three down full travelling cycles (doors closing, acceleration, constant speed, deceleration and doors opening) were measured from the bottom to the top floor and back and the time data was the basis for the following sound-quality analysis.

The equipment used consisted of Bruel and Kjaer's Sound Quality Head and Torso Simulator (HATS) Type 4100-D, equipped with two microphones for binaural noise measurements. The two signals were recorded using a Pulse IDAe front-end and time data recorder software. 'The Pulse front-end is useful for measurements inside a moving lift as it makes no noise at all (its fan can be switched off during measurements) and it can be battery operated. 'Besides, time data recorder software is extremely simple to configure and use for time data measurements,' added Galfarsoro.

Comments

Post a Comment

Popular posts from this blog

Han® HC 250 high current contact

A Powerful Solution HARTING has developed the new Han® HC 250high current connector as a powerful interface that impresses by requiring little space, transmitting high current intensities and allowing flexible configuration of the number of poles. The HC 250 one-pole crimp module can be connected in various frame geometries to produce the required number of poles in a compact space – and in the existing Han® HPR housing. Technical details: - Rated current 250 A at a rated voltage of 2000 V - Termination cross-sections are: 35 mm2, 50 mm2 and 70 mm2 - Maximum four-pole interfaces in a size 24 B HPR housing, making it particularly suitable for motor connections - High quality plastic with good smoke and inflammability levels - Removal tool for simple installation and removal of the contacts and inserts - Confusion of a number of interfaces is reliably prevented by multiple coding options for the individual inserts The requirements in the railway industry are changing, as
Read more

EGCS-D0 Accelerometer Now Available in 10,000g Range

Measurement Specialties, Inc. (NASDAQ: MEAS) has recently redesigned the EGCS-D0 accelerometer to enable it to accurately and reliably measure up to ±10,000g. This rugged device is critically damped, which is the ideal mechanism to protect the accelerometer against ±20,000g impacts and prevent sensor ringing. The EGCS-D0 accelerometer is now available in ranges from ±5g to ±10,000g which makes it ideal for both critical low-g measurements and high-g impacts. These units feature a Wheatstone Bridge mV output with a standard compensated temperature range of 20ºC to 80ºC (other options available). The EGCS-D0 was specifically designed for impact and shock testing in auto safety, aerospace, military and civil engineering applications. Designed to be bolt-mounted, this device operates from 2-15Vdc excitation with electrical output ratiometric to voltage input. Optional triaxial mounting blocks (MTG-F4), signal conditioners (Model 101) and auto-zero inline amplifiers (Model 140) are avai
Read more
Ilix Cermet Reamers Are Ideal For Dry Machining Engineers Cutting Tools, the UK agent for Ilix, has introduced Ilix solid-carbide and cermet reamers for the machining of hard metals. The machine reamers 6372C and 6323 allow the production of high-precision holes with good surface finish. Compared with HSS, the solid-carbide qualities enable the increase of cutting parameters and tool life. The quality of the reamers is said to guarantee high performance, even for hard metals with a resistance more than 1200N/mm2. The Ilix carbide 6372C range of hundredth reamers is from 0.98mm through to 12.05mm in increments of 0.01mm. The reamers are manufactured to a tolerance of +0.000 - +0.004mm. The cermet reamers 6323 have new cutting geometry developed by Ilix. These reamers are said to be ideal for steel machining, having high chemical stability during the cutting process. They offer good wear resistance due to the high hardness and have low material adhesion. The Ilix cermet reamer is said to
Read more